VoltVanguard

How to Choose a Power Station for Your Irrigation Controller

Updated November 2026

Quick answer: Most residential irrigation controllers and their solenoid valves draw only 5 to 25 watts, so a compact power station easily rides out an outage and keeps a watering schedule on track. The Anker SOLIX C300 is the best overall pick for its quiet, always-on standby power and 288Wh of reserve. The Jackery Explorer 300 Plus is a strong runner-up at a lower price if you do not need the extra port options.

A power outage rarely announces itself, and an irrigation controller that loses power mid-cycle can leave a zone running for hours or skip a scheduled watering entirely during a heat wave. For homeowners managing drip irrigation, sprinkler zones, greenhouse beds, or livestock troughs with electronic timers, a dedicated power station is the simplest way to keep the controller and its solenoid valves alive through a blackout, a tripped breaker, or a remote installation with no nearby outlet. This guide breaks down exactly how much power an irrigation controller actually needs, which power station sizes make sense for different setups, and how to wire a reliable backup system that will not let your beds dry out.

How Much Power Does an Irrigation Controller Actually Need?

Irrigation controllers themselves are remarkably low-draw devices. The electronics inside a typical controller, including the display, Wi-Fi radio, and logic board, pull somewhere between 2 and 8 watts continuously. The real draw comes when a solenoid valve opens. Most residential 24VAC solenoid valves need a brief surge of 7 to 10 watts to open (the "inrush" moment) and then settle to roughly 3 to 5 watts to stay open while watering. If you run multiple zones sequentially rather than simultaneously, as nearly all residential systems do, you are rarely drawing more than 15 to 20 watts total at any instant.

Commercial or multi-zone agricultural setups that open several valves at once, or that pair the controller with a booster pump, change this math substantially. A single fractional-horsepower pump can draw 500 to 1,500 watts on startup, which pushes you into a completely different class of power station than the one you would pick for the controller alone.

Types of Irrigation Controllers and Their Power Profiles

Not every controller draws power the same way, and knowing which category yours falls into changes how you size a backup.

  • Smart Wi-Fi controllers (Rachio, Hunter Hydrawise, Rain Bird smart models) keep a radio active around the clock to sync schedules and weather data. These typically draw 3 to 6 watts at idle, slightly more than older analog timers, because the Wi-Fi radio never fully sleeps.
  • Basic hardwired timers without smart features draw closer to 1 to 3 watts at idle, since there is no radio or cloud sync running in the background.
  • Battery-powered standalone timers, the kind that screw directly onto a hose bib, run on AA or lithium coin cells rather than AC power, so they are not a candidate for power station backup at all; a power station only matters for the AC-powered, transformer-fed controllers that run whole-yard or multi-zone systems.
  • Agricultural and greenhouse controllers that manage several zones plus sensors (soil moisture, flow meters, rain sensors) draw more continuously, often 8 to 15 watts, because they are polling multiple inputs rather than just a clock.

Across all of these categories, the valve itself, not the controller board, remains the biggest single draw, and it only happens while water is actively flowing.

Real-World Sizing Scenarios

SetupTypical LoadRecommended Power Station
Small home garden, 2-4 zones, single valve open at a time5-15WAnker SOLIX C300 or Jackery Explorer 300 Plus
Greenhouse drip system with moisture sensors10-20WAnker SOLIX C300
HOA or community garden, multiple valves, shared controller15-30WAnker SOLIX C300, step up to C800 Plus if valves overlap
Farm trough float-valve system with small booster pump300-900W surgeAnker SOLIX C800 Plus or C1000 Gen 2

A small home garden or greenhouse setup rarely needs anything beyond the smallest unit on this list. Where people over-buy is when they size for a theoretical worst case that their actual valve wiring never produces, since most residential manifolds are wired to open one zone at a time specifically to avoid the pressure and power drop of simultaneous valves.

Comparison: Power Stations for Irrigation Controller Backup

Power StationCapacityContinuous OutputEst. PriceBest For
Anker SOLIX C300288Wh300W$$Controller + valves, multi-day standby, quiet operation
Jackery Explorer 300 Plus293Wh300W$Budget backup for controller + valves only
Anker SOLIX C800 Plus768Wh800W$$$Controller plus a small booster or well pump
Anker SOLIX C1000 Gen 21,056Wh1,500W$$$$Multi-zone commercial setups or pump-assisted irrigation

Best Overall: Anker SOLIX C300

For a standard residential drip or sprinkler controller, the Anker SOLIX C300 is the pick we would buy. At 288Wh and a 300W continuous rating, it has far more headroom than a controller and a couple of valves will ever use, which means it can sit at low, steady draw for days between recharges rather than being pushed near its limit. Its standby efficiency is particularly good: because the controller only pulls a few watts most of the time, the C300 will run it for well over a week on a single charge if nothing else is attached. It also recharges quickly from a wall outlet or a small solar panel, which matters if the controller is mounted outside, far from the house, in a garage, or on a fence post near the garden.

See the full Anker SOLIX C300 review for the complete spec breakdown, including runtime tables for other low-draw devices.

Best Budget Pick: Jackery Explorer 300 Plus

If you only need to keep the controller and valves alive and do not care about extra passthrough ports or app monitoring, the Jackery Explorer 300 Plus gets the job done for less money. At 293Wh and a 300W continuous rating, it matches the C300 on paper for this specific use case. The trade-offs are slower AC recharging and fewer ports, neither of which matters much for a device that draws single-digit watts most of the time. Read the full Jackery Explorer 300 Plus review for where it falls short of the Anker in other use cases.

When You Need More: Pump-Assisted and Multi-Zone Systems

If your irrigation setup includes a booster pump, a well pump feeding a drip line, or a controller that opens several valves simultaneously for a commercial or large-acreage layout, step up to a larger unit. The Anker SOLIX C800 Plus (768Wh, 800W continuous) comfortably absorbs the startup surge of a small pump, and the Anker SOLIX C1000 Gen 2 (1,056Wh, 1,500W continuous) gives enough headroom for most fractional-horsepower pumps plus the controller itself. Oversizing by one tier is cheap insurance against a pump's startup surge tripping the unit's overload protection.

How to Wire the Backup Correctly

  • Use the controller's existing transformer. Most irrigation controllers plug into a wall-mounted 24VAC transformer. Plug that transformer into the power station's AC outlet exactly as you would a wall outlet; do not try to bypass it and wire the power station directly to the valve wiring.
  • Keep the power station dry and ventilated. If the controller lives in a garage or a weatherproof enclosure outdoors, place the power station in a dry, shaded spot nearby, never exposed to rain or direct irrigation spray.
  • Add a small solar panel for unattended installations. A remote garden, greenhouse, or pasture controller that nobody checks daily benefits from a trickle-charging solar panel so the power station never runs down between visits. Our solar panel sizing guide covers matching panel wattage to a small, low-draw load like this one.
  • Test before the growing season starts. Run the controller on battery alone for a full watering cycle before you need it for real, so you know actual runtime rather than a manufacturer estimate.

Solar-Only vs. Battery-Plus-Solar Hybrid Setups

For a controller mounted far from any outlet, such as one serving a back pasture, a detached greenhouse, or a community garden plot with no electrical hookup, you have two real options. A solar-only setup pairs a small panel directly with a charge controller and a 12V battery, which works but leaves the controller vulnerable on cloudy stretches with no reserve beyond the battery's own capacity. A battery-plus-solar hybrid, where a power station's larger internal battery is topped off by a modest panel whenever the sun is out, is more forgiving: the power station's reserve smooths over several consecutive overcast days that would otherwise interrupt watering. For a controller drawing under 20 watts, even a 60 to 100 watt foldable panel keeps a 288Wh power station topped up through a full watering season in most climates, and the 100W foldable solar panel options on Amazon are a good starting point for this scale of load.

Common Mistakes to Avoid

The most common mistake is buying a power station sized for the controller's average draw rather than its worst case. A controller that spikes briefly when three valves share a manifold and open close together can trip a small inverter's overcurrent protection even though the average load looks tiny. The second mistake is ignoring standby drain: a power station's own idle consumption, typically 2 to 5 watts, adds up over the days between recharges and should be included when estimating total runtime. Finally, avoid running a battery all the way to zero on a schedule you cannot monitor; set a low-battery alert or check the unit's app periodically so a drained battery during a heat wave does not leave your garden unwatered.

For general sizing guidance across all kinds of devices and loads, see our how to choose a power station guide and the power station wattage calculator for working out your specific numbers.

Frequently Asked Questions

Can a power station run my irrigation controller through a multi-day outage?

Yes. Because most residential controllers and their valves draw well under 20 watts, even a compact 288Wh power station can run one for a week or more on a single charge, as long as nothing else is drawing power from the same unit.

Do I need an inverter-based power station, or will a basic battery work?

Use a power station with a built-in pure sine wave inverter rather than a basic 12V battery and a separate charger. The transformer feeding most irrigation controllers expects clean AC power, and a pure sine wave output avoids the buzzing or erratic behavior that modified sine wave or square wave power can cause in transformer-based electronics.

What size power station do I need if my irrigation system includes a booster pump?

Size for the pump's startup surge, not its running wattage. A small booster pump that runs at 300 watts can surge to 600 to 900 watts for a second on startup, so choose a power station rated for at least that peak, such as the Anker SOLIX C800 Plus or larger.

How long will the power station last on standby between waterings?

Idle standby drain from the controller itself, typically 2 to 8 watts, plus the power station's own idle draw of 2 to 5 watts, means a 288Wh unit can sit ready for well over a week between full waterings, and considerably longer if you add a small solar panel to trickle-charge it.

Should I leave the power station connected permanently, or only during outages?

For remote or unattended installations, leaving it connected permanently with a solar trickle charge is more reliable than swapping it in only during an outage, since you will not be on-site to notice the power has failed until a zone misses its schedule.